loading

KAESID - One stop solution for commercial kitchen equipment.

Case Study: Two Years, Four Pitted Pots — How a Coastal Pasta Kitchen Switched to 316

Client profile — A three-site Italian restaurant group in a coastal city, roughly 180 covers per site, pasta-forward menu with 22–28 pasta dishes on rotation. Two gas pasta cookers per kitchen, running 9–11 hours a day.

The problem — Every 20–24 months the group replaced its pasta pots. Not the burners, not the thermostats: the pots. Pitting appeared first around the drain fitting and along the water line, then rust bloom spread across the bottom. One site failed a supplier audit on "excessive corrosion in a food-contact vessel" and had to replace a pot mid-quarter.

By the time they called us, the group had spent years treating pot replacement as a running cost of doing pasta.

 Kaesid gas pasta cookers

What the diagnosis actually showed

The pots were 304 stainless — the correct, cost-efficient grade for most kitchen equipment, and still the right choice for fryer pots, work tables and cabinet panels. But three conditions in this kitchen added up badly:

  • Salted boiling water, all day. Chloride ions attack the passive chromium-oxide layer of 304 locally, starting pinhole pitting that grows from the inside of the wall.
  • Overnight standing water. Staff left salted water in the pot overnight "to save time in the morning". Standing chlorides at ambient temperature keep working on the metal long after service ends.
  • Weld zones. Pitting concentrated around the drain fitting weld, which is normal — weld heat destroys the passive layer unless the joint is pickled and passivated afterwards.

None of this is a manufacturing defect. It is a grade-to-duty mismatch: a 304 vessel asked to do 316 work.

The change

We specified the PC11 gas pasta cooker with a 316 stainless steel water pot: 11 gallons, open-pot design, 70,000 BTU stainless tube burner, 212–257°F thermostat with high-limit protection, 1-inch full-port drain. The 316 grade adds 2–3% molybdenum, which stabilizes the passive layer against chloride attack — marine-grade stainless, in a boiling salt-water application.

Two process changes came with the hardware, and they mattered as much as the alloy:

  • Drain and dry at close. The full-port valve empties 11 gallons in minutes, and the open pot wipes down without reaching into a closed vessel.
  • No overnight brines. Salt water goes down the drain, not into the next morning.

The numbers after 14 months

Item Before (304 pots) After (316 pot)
Pot replacement cycle Every 20–24 months No replacement to date (14 months, no pitting)
Replacement cost per site per year ~1 pot / 2 years, plus freight and downtime Zero to date
Downtime for pot swap 1 service day per replacement None
Audit findings 1 failed audit (corrosion) Clean at last review

The payback is not subtle. A 316 pot costs more at factory level — modestly, not dramatically — and it removed a recurring line item plus a service-day loss per replacement cycle. Multiply by three sites and the arithmetic does itself.

What the kitchen team noticed that we did not expect

The operations manager's feedback was about labour, not metallurgy: with the open pot and the 1-inch drain, close-down on the pasta station dropped by roughly 15 minutes a shift. The starch overflow tube also cut the frequency of scrubbing burnt foam off the burner area — the failure mode that quietly eats a commis chef's evening.

Three lessons for buyers specifying pasta equipment

  • Match grade to duty, not to catalog defaults. 304 for dry heat, 316 for salted boiling water. A supplier who quotes 316 on fryer pots is over-specifying; one who quotes 304 on pasta pots is under-specifying.
  • Ask for the bill of materials, not the brochure. "Stainless steel pot" tells you nothing. Ask which components are 316 and request mill test certificates on the pot alloy.
  • Process is half the specification. Even 316 will pit if salted water stands in it overnight. Buy the right grade, then train the close-down routine.

Considering the same change?

If your pasta station is replacing pots every two years, the upgrade usually pays back inside one replacement cycle. Kaesid supplies the gas pasta cooker with a 316 water pot factory-direct, with material documentation on request, OEM/ODM branding and wholesale pricing for distributors and chains. Send us your current pot spec and duty cycle, and we will quote the 316 equivalent.

prev
Industrial Canteen Equipment: How Kaesid Delivers Tailored Solutions for Global Foodservice Operators
recommended for you
Get in touch with us

Overall solution for commercial kitchens.

Find us here:

Contact with us
Contact person: Miss.Sally
Tel: +86 173 0440 9196
WhatsApp: +86 173 0440 9196
Add

Plant 2025, Building A, Basda Building, 28 Nantong road, Baolong Street, Longgang District, Shenzhen, China.

Copyright © 2026 KAESID | Sitemap | Privacy Policy
Customer service